Friday, December 31, 2010

Lancia Lambda, 1926

Lancia Lambda, 1926



The Lancia Lambda was an innovative automobile produced from 1922 through 1931. It was the first car to feature a load-bearing monocoque-type body, and it also pioneered the use of an independent suspension (the front sliding pillar with coil springs). Lancia even invented a shock absorber for the car. Approximately 11,200 Lambdas were produced.

The narrow-angle aluminum Lancia V4 engine was also notable. All three displacements shared the same long 120 mm stroke, and all were SOHC designs with a single camshaft serving both banks of cylinders.

Engines
    * 2119 cc (75 mm bore, 13° vee), 49 hp (36.5 kW) at 3250 rpm
    * 2370 cc (79.37 mm bore, 14° vee), 59 hp (44 kW) at 3250 rpm
    * 2568 cc (82.55 mm bore, 13°40' vee), 69 hp (51.5 kW) at 3500 rpm

Lancia Theta 35HP, 1913

Lancia Theta 35HP, 1913



Lancia Theta 35HP, 1913

Lancia Lambda, 1922

Lancia Lambda, 1922





Lancia Lambda, 1922

Thursday, December 30, 2010

Renault Dauphine, 1957

Renault Dauphine, 1957



The Renault Dauphine was an automobile produced by the French manufacturer Renault from 1956 to 1962. A luxury version, badged as the Renault Ondine was sold from 1960 to 1962.

The Dauphine was launched in 1956 to replace the highly successful Renault 4CV. Like the 4CV, the Dauphine used a single-shell monocoque body. It was a four-door sedan design as was the 4CV (but it lacked the rear-hinged "suicide doors" of the 4CV). It was also heavier and 12 inches longer than its predecessor, but used the same engine, albeit a version increased in size and power from 760 cc to 845 cc and 19 hp to 32 hp (14 to 24 kW) (the Dauphine was infamously slow: Road & Track magazine measured the Dauphine's 0-60 mph acceleration time as 32 seconds). The Dauphine was originally intended to be called the Corvette, but was changed to Dauphine (the female form of the French feudal title of Dauphin) to avoid confusion with the recently-launched Chevrolet Corvette.

Two limited editions of the Dauphine tuned to get more power from the engine were launched during its lifetime: firstly, Renault performance guru Amedee Gordini (who was to later produce high performance versions of the Renault 8, Renault 12 and Renault 15 among others) engineered a version of the Dauphine tuned to 37 hp (27.2 kW), which was sold as the Dauphine Gordini. Also, the final run of Dauphines, a limited edition of 1000 called the 1093, were similarly tuned to 55 hp (41 kW) and featured a twin barrel carburetor, rear track rods, five-speed manual transmission and tachometer, and had a top speed of 140 km/h. The 1093 was only available in white with two blue stripes down each side. A luxury version of the Dauphine called the Ondine was sold during the last two years of its prodution run.

A version of the Dauphine Gordini, called simply the Renault Gordini, was manufactured in Brazil under license by Willys-Overland.

Among the many aftermarket options available for the Dauphine were a supercharger designed by American company Judson Research & Mfg. Co, sold in 1958 for US$165, and designed to be installed in about two hours without any chassis or body modifications.

The Dauphine's legacy is somewhat dominated by both its infamously poor performance as well as its poor reliability: in many markets (particularly the United States and the United Kingdom) the car became notorious for mechanical problems and rust issues. In 2002, the auto enthusiasts' website Car Talk voted the Dauphine the 9th Worst Car Of The Millennium, calling it "truly unencumbered by the engineering process". Nevertheless, it remains popular as an antique/classic car, particularly in Europe.

Renault 4 CV Sport, 1954

Renault 4 CV Sport, 1954




The Renault 4CV was an automobile produced by the French manufacturer Renault from 1946 to 1961. An economical "people's car" inspired by the Volkswagen Beetle, it was the first French car to sell over a million.

The 4CV was originally conceived and designed covertly by Renault engineers during the German occupation of France during World War II, when the manufacturer was under strict orders to design and produce only commercial and military vehicles. A design team led by Fernand Picard, Charles-Edmond Serre and Jean-Auguste Riolfo envisioned a small, economical car (similar to the Volkswagen Beetle) suitable for the economically difficult years which would inevitably follow the war. The first prototype was completed in 1942 and two more prototypes were produced in the following three years, with the 4CV ultimately presented to the public and media at the 1946 Paris Motor Show.

On the 4CV's launch, it was nicknamed "La motte de beurre" (the lump of butter) due to the combination of its shape and the fact that many early models were painted with sand yellow-colored German army surplus paint intended for the Afrika Korps. The 4CV was powered by a 748 cc engine producing 17 hp, which was coupled to a three-speed manual transmission. Despite an initial period of uncertainty and poor sales due to the ravaged state of the French economy, the 4CV had sold 37,000 units by mid-1949 and was the most popular car in France. The car remained in production for more than a decade afterwards; it was intended to be replaced by the Renault Dauphine, launched in 1956, but the 4CV in fact remained in production until 1961, only a year earlier than the more expensive Dauphine was discontinued. In event, it was replaced by the Renault 4 which used the same engine and name as the 4CV and sold for a similar price.

1,105,547 cars were produced; the 4CV became the first French car to sell over a million.

The 4CV was easily modified and was used extensively as a racing car, winning both the Le Mans 24 Hours and the Mille Miglia. The first collaboration between the Alpine company and Renault, a partnership which would go on to win the World Rally Championship with the legendary Alpine A-110 in later years, was the Alpine A-106 which was based on the 4CV.
 

Honda Civic CVCC, 1975

Honda Civic CVCC, 1975



The Honda Civic is an automobile manufactured by Honda. It was introduced in July 1972 as a two-door coupe, followed by a 3-door hatchback version that September. With the transverse engine placement of its 1169 cc engine and front wheel drive, like the British Mini, the car provided good interior space despite overall small dimensions.

Early models of the Civic were typically outfitted with a basic AM radio, rudimentary heater, foam cushioned plastic trim, two-speed wipers, and painted steel rims with a chromed wheel nut cap. The current Civic has become much more luxurious with satellite-linked navigation, a six-speed manual, power locks and power windows available. Still, many regard the Civic as representing a good value for the money, combining good performance, reliability and economy, as well as a very low rate of depreciation.

The Civic evolved from having a 1170 cc engine (1973) to having engines with larger capacities and more creature comforts (air conditioning, power windows, etc.) through the 1980s, 1990s and into the 2000s.

First generation (1973-1979)

The original 1973 Civic had a wheelbase under 87 inches and an overall length of 140 inches

Initially the Civic was sold with either a four-speed manual or a two speed "HondaMatic" model. Later models went to a five-speed manual and a full four-speed automatic transmission. Like the Mini, the transaxle was integrated with the engine unit.

Second generation (1979-1983)

The second generation Civic had a new, sleeker body and increased wheelbase to 88.6 inches for the hatchback and 91.3 inches for the wagon. The two-door sedan was no longer produced. All engines was now of the CVCC design ranging from 1335 cc giving 55 hp to 1488 cc giving 67 hp. The transmission was either a four-speed manual, a five-speed manual or a two-speed automatic. In 1981 a four door sedan was introduced and the two-speed automatic gearbox was replaced by a three speed. In 1982 it was slightly restyled with rectangular headlamps and black bumpers. In 1983 the sportier Civic S replaced the 1500GL.

Third generation (1983-1987)

For the third generation the wheelbase was increased by 5 inches to 96.5 inches. A new 12 valve (three valves per cylinder) 76 hp 1500 cc engine was introduced. The base hatchback still used the 1300 cc engine giving 60 hp. Supension was updated to independent rear suspension. The CRX was a Civic with a slightly different body. In 1985 the CRX Si was introduced. It came with a fuel-injected version of the 1500 cc engine giving 91 horsepower. In 1986 the Civic got flush-mounted headlights. Other news for the year was a four-speed automatic and an Si version of the Civic hatchback.

Fourth generation (1987-1991)

Again the wheelbase was increased to 98.4 inches. The body was designed with lower hood line and more glass giving less drag. The Civics also got a new family of engines. A 1500 cc 16-valve engine giving 92 hp was used in the DX hatchback/sedan, new LX sedan and the wagon. The base hatchback had a 70 hp version of the same engine. All engines were fuel injected. All wheels had double-wishbone suspension. In 1990 the EX trim was introduced.

Fifth generation (1991-1995)

The fifth generation had a more wedge shaped body and the wheelbase was increased to 101.3 inches for the two-door hatchback and 103.2 inches for the four-door sedan. The wagon was also dropped.

Sixth generation (1996-2000)

Beginning in 1997, Honda produced the first iteration of Civic to receive the "Type-R" appellation (applied first to the Integra Type-R), with the EK9 chassis Civic Type-R. The EK9-generation Civic Type-R had a maximum output in the range of 180 PS JIS (177 hp/132 kW), increased over the more common 160 PS (158 hp/118 kW) B16A engine in the SiR/VTi models, and included various alterations to the chassis to improve handling and reduce weight (such as better welding of the frame, and removal of the radio and noise-suppressing materials).

Seventh generation (2001-2005)

In 2001, Honda announced the release of the Civic Type-R for the EP chassis, a more sporty variant of the most recent model of Civic and successor to the EK9 Civic Type-R. Unlike the EK9 version, which was produced solely in Japan, the EP Civic Type-R is produced in the United Kingdom and exported to Japan. The EP Civic Type-R has a specific output of 200 PS (197 hp/147 kW) at 8000 rpm, a six-speed manual transmission, a reworked exterior with a bullet-like hatchback design, aeroform bumpers, spoiler, and 17 in wheels. The interior of the Type-R includes Recaro seats and a Momo steering wheel, and the model also includes Type-R-specific badging, a helical limited-slip differential, and has been reported to accelerate from zero to 60 mph in about 6.6 seconds (6.4 in facelifted model).

The hybrid version became available in 2003, which uses both a small (1.3 L) main gasoline engine and auxiliary electric motors. The electric motors are powered by a battery array which is charged by regenerative braking during deceleration, which reduces exhaust emissions and extends fuel mileage.

The new Sport Hatchback model with futuristic styling was unveiled in August 2005 for the European market only. This model featured from launch a 1.4 L I-DSI and a 1.8 L i-VTEC rated at 83 PS (81 hp/61 kW) and 140 PS (138 hp/103 kW) respectively, with 177 and 207 km/h (110 and 129 mph) top speeds and 14.2 and 8.6 sec 0-100 km/h sprint. The Sport Hatchback is also available with a 2.2 L I-CTDI Diesel engine from the Accord, Edix/FR-V and CR-V, rated at 140 PS (138 hp/103 kW) and is capable of 205 km/h (127 mph) and accelerating from 0-60 mph in 8.4 seconds.

Honda Accord Hatchback, 1976

Honda Accord Hatchback, 1976




The Honda Accord is an automobile manufactured by Honda. The Accord was introduced in 1976 as a compact hatchback, with styling similar to an upsized contemporary Honda Civic. A four-door sedan was debuted in 1977.

First generation (1976–1981)

The first generation Honda Accord was launched in 1976 as a two-door hatchback with 68 horsepower, a 93.7-inch wheelbase, and a weight of about 2,000 pounds. It was larger than the tiny Civic at 162 inches long. The Accord sold well, due to its moderate size and great fuel economy. In 1978 an LX version of the coupe was added which came with air conditioning. In 1979 a four-door sedan was added to the lineup, and horsepower went to 72 horsepower. In 1980 the optional two-speed automatic of previous years became a three-speed automatic. In 1981 an SE model was added for the first time, with leather seats.

Second generation (1982–1985)

In 1982, the Accord was redesigned, and it became the best-selling Japanese nameplate in the US, holding that position for 15 years. Modernizing both the interior and exterior, the second generation Accord was mechanically very similar to the original, using the same 75hp, 1751cc EK1 CVCC engine. Fuel economy was increased by nearly 15%. Vastly improved quality control, however, made this one of the most reliable cars on the US market, a position it still holds today.

In 1983, Honda used a four speed automatic transmission in automatic models, a major improvement over the three speed Hondamatic.

By 1984 Accords sold in the eastern US were being produced at the new Marysville, Ohio plant with quality considered equal to those produced in Japan. The body was restyled with a slightly downward beveled nose, and the slightly more powerful ES2 1829cc CVCC powerplant was used, bringing 86hp. The LX offered most features typical of a mid-price Buick or Chrysler such as velour upholstery, cassette stereo, air conditioning, power brakes & steering, power windows, power locks, powered sunroof and roof pillar antenna, along with thick black belt moldings and integrated bumpers. Flush plastic mock-alloy wheels covers instead of caps on steel wheels that resembled the trend-setting Audi 5000. Supplies were tight, as in the Eastern states, the wait was months for a graphite gray sedan, a then-popular color. These models are still common on US roads today.

In 1985 the luxury SE-i was added, which had leather seating, bronze tinted glass, and 14" alloy wheels. A fuel injected, 110hp non-cvcc A2OA1 made its debut. This 12 valve, 1955cc engine was the first non-CVCC engine used in an Accord. The same basic engine was used by Honda until 1989.

Third generation (1986–1989)

The third generation Accord was introduced in Japan and Europe in 1985 and the rest of the world in 1986. The Accord had a very striking shape, and looked more akin to a sports car than a conventional 3-box sedan. It bore a resemblance to the second and third generation Prelude. One notable feature was the flip-up headlights, extremely unusual for a sedan. A fixed headlight version appeared in 1987 for European and Japanese markets. The fixed headlight version also had a different tailight cluster.

The 3rd Generation's suspension was a double wishbone setup, which was derived from Honda's work in Formula one. While this setup was more expensive than competitors' Macpherson Strut systems, it provided better stability and sharper handling. All 86-89 Accords Have front and rear stabilizer bars. The Accord's brakes were either Large 4-wheel discs with twin-piston calipers ( as in the JDM Si model), smaller 4-wheel discs with single piston calipers, or a Front Disc/Rear Drum system. ABS was also available as an option on the 4-wheel disc brake models, although this was never offered in North American versions of the car. Base model Accords rode on 13-inch steel wheels with hubcaps, with more expensive models having the option of 14-inch alloy wheels.

The most recent addition to Honda's museum of used cars, a 1989, third generation, Honda Accord SEI owned by U.S. resident Jason Wong has survived through numerous crashes caused by blatantly bad driving, and has over 400,000 miles on it.

Wednesday, December 29, 2010

Citroen DS 19 Cabrio, 1964

Citroen DS 19 Cabrio, 1964


The Citroën DS (also known as Déesse, or Goddess, after the punning initials in French) was an automobile produced by the French manufacturer Citroën between 1955 and 1975. Citroën sold nearly 1.5 million D-series during its 20 years of production.The DS is well-known for its futuristic, aerodynamic body design, and for its innovative technology (including its hydropneumatic self-leveling suspension system).

The DS advanced the achievable standards in terms of ride quality, roadholding, handling, and braking in an automobile. Automotive journalists of the time often noted that competitors took decades to adapt to the higher standards it set. The smooth, aerodynamic body lines gave the car a futuristic appearance. While it looked very unusual in 1955, public tastes appear to have caught up with the DS in the post-Ford Taurus/Audi 100 era.

Model history

After 18 years of development in secret as the successor to the venerable Traction Avant, the DS 19 was introduced on October 5, 1955 at the Paris Motor Show. The car's appearance and innovative engineering captured the imagination of the public and the automobile industry almost overnight. 743 orders were taken in the first 15 minutes of the show, and orders for the first day totalled 12,000.

Far from being just a fascinating technology in search of a purpose, contemporary journalists were effusive in noting how the DS dramatically pushed the envelope in the ride vs. handling compromise possible in a motor vehicle.

The high price tag, however, hurt general sales in a country still recovering from World War II 10 years earlier, and a submodel, the ID (another pun: in French, Idée, or Idea), was introduced in 1957 to appeal to more cost-conscious buyers. The ID shared the same body with the DS, but had more traditional features under the hood. It had no power steering (though this was added as an option later), and instead of the hydraulically controlled manual transmission and clutch, it had a conventional clutch and transmission. Interestingly, the first model series was called 11D, a clear reminder of the last model of the Traction Avant, the 11C. A station wagon variant, the ID Break, was introduced in 1958.

Outside of France, the car's radical and cosmopolitan design appealed to non-conformists. A United States advertisement summarised this selling point: "It takes a special person to drive a special car".

Throughout its model lifetime, the DS managed to remain ahead of its time. It featured power disc brakes, a hydropneumatic suspension including an automatic levelling system and variable ground clearance, power steering and a semi-automatic transmission. A fiberglass roof reduced weight transfer. Inboard front brakes (as well as an independent suspension) reduced unsprung weight. Different front and rear track widths and tire sizes reduced the understeer typical of front-engined and front-wheel drive cars.

Despite the rather leisurely acceleration afforded by its small four-cylinder engine, the DS was successful in motorsports like rallying, where sustained speeds on poor surfaces are paramount.

The DS came in third in the 1999 Car of the Century competition, recognizing the the world's most influential auto designs. Winner and second place went to the Ford Model T and the Mini. It placed fifth on Automobile Magazine "100 Coolest Cars" listing in 2005.

Technical innovations
Hydraulic system
The hydraulic system of the DS 19 was a revolution. Previously hydraulics had been restricted to use in brakes and power steering; the DS used them for the suspension, clutch and transmission. The later ID19 had manual steering and a simplified power braking system.

Suspension

At a time when few passenger vehicles had caught up with the four-wheel independent suspension of the Traction Avant, the application of the hydraulic system to the car's suspension system to provide true self-levelling was a stunning move. This application - 'hydropneumatic suspension' - was pioneered the year before on the rear of the top of range Traction Avant 15CV-H.

At first it was often described as air/oil suspension, since both elements played a key role.

Each wheel was connected not to a spring, but to a hydraulic suspension unit consisting of:
    * a sphere of about 12 cm in diameter containing pressurised nitrogen
    * a cylinder containing hydraulic fluid screwed to the suspension sphere
    * a piston inside the cylinder connected by levers to the suspension itself
    * a damper valve between the piston and the sphere

A membrane in the sphere prevented the nitrogen from escaping. The motion of the wheels translated to a motion of the piston, which acted on the oil in the nitrogen cushion and provided the spring effect. The damper valve took place of the shock absorber in conventional suspensions.

The hydraulic cylinder was fed with hydraulic fluid from the main pressure reservoir via a height corrector, a valve controlled by the mid-position of the anti-roll bar connected to the axle. If the suspension was too low, the height corrector introduced high-pressure fluid. If it was too high, it released fluid back to the fluid reservoir. In this manner, it maintained a constant height. A control in the cabin allowed the driver to select one of five heights:
    * normal riding height.
    * two slightly higher riding heights, for poor terrain.
    * two extreme positions for changing wheels.

The DS did not have a jack for lifting the car off the ground. Instead, the hydraulic system enabled wheel changes with the aid of a simple adjustable stand.

Source and reserve of pressure
The central part of the hydraulic system was the high pressure reservoir, which maintained a pressure of between 130 and 150 bar in two accumulators. These accumulators were very similar in construction to the suspension spheres. One was dedicated to the brakes, and the other ran the other hydraulic systems. Thus in case of a hydraulic failure (a surprisingly infrequent occurrence), the first indication would be that the steering became heavy, followed by the gearbox not working; only later would the brakes fail.

Hydraulic fluid
The original hydropneumatic system used a vegetable oil (LHV or liquide hydraulique végétale) similar to that used in other cars at the time. Very soon, Citroën changed to using a synthetic fluid (LHS or liquide hydraulique synthétique). Both of these had the disadvantage that they are hygroscopic, as is the case with most brake fluids. Disuse allows water to enter the hydraulic components causing deterioration and expensive maintenance work. The difficulty with hygroscopic hydraulic fluid was exacerbated in the DS/ID due to the extreme rise and fall in the fluid level in the reservoir, which went from nearly full to nearly empty when the suspension "got up" and the 6 accumulators in the system filled with fluid. With every "inhalation" of fresh moisture- (and dust-) laden air, the fluid absorbed more water. In August 1967, Citroën introduced a new mineral oil-based fluid LHM, or liquide hydraulique minérale. This fluid was much less aggressive on the system and it remains in use to the present day.

Briefly illegal in the United States (US federal law requires motor vehicle brake fluid to be red - an exception had to be granted to Citroën), LHM has since been adopted by manufacturers like Rolls-Royce, Jaguar, BMW, and Audi under different labels, like "Total," "Pentosin," and others.

LHM required completely different materials for the seals. Using either fluid in the incorrect system would completely destroy the hydraulic seals very quickly. To help avoid this problem, Citroën added a bright green dye to the LHM fluid and also painted all hydraulic elements bright green. The former LHS parts were painted black.

Several different hydraulic pumps were used. The DS used a seven-cylinder axial piston pump driven off two belts and delivering 175 bar of pressure. The ID19, with its simpler hydraulic system, had a single cylinder pump.

Gearbox and clutch
The mechanical aspects of the gearbox and clutch were completely conventional and the same elements were used in the ID 19.

The gear change control consisted of:
    * Hydraulic gear selector.
    * Clutch control. This was the most complicated part. The speed of engagement of the clutch was controlled by:
    * A centrifugal regulator, sensing engine rpm and driven off the camshaft by a belt
    * The position of the butterfly valve in the carburettor (i.e. the position of the accelerator)
    * The brake circuit: when the brake was pressed, the engine idle speed dropped to a rpm below the clutch engagement speed, thus preventing friction while stopped in gear at traffic lights. When the brake was released, the idle speed increased to the clutch dragging speed. The car would then "creep" much like automatic transmission cars. This drop in idle throttle position also caused the car to have more engine drag when the brakes were applied even before the car slowed to the idle speed in gear, preventing the engine from "pulling" against the brakes.

Impact on Citroën brand development

The 1955 DS in one stroke cemented the Citroën brand name as an automotive innovator. In fact, the DS caused such a huge sensation that Citroën was fearful future models would not be bold enough. Other than variations on the very basic 2 cylinder economy car Citroën 2CV, like the Citroën Ami, no new models were introduced from 1955 to 1970.

The DS was a large, expensive executive car and a downward brand extension was attempted, but without result. Throughout the late 1950s and 1960s Citroën developed many new vehicles for the very large market segments between the 2CV and the DS, occupied by vehicles like the Peugeot 403, Renault 16 and Ford Cortina. None made it to production. Either they had uneconomic build costs, or were ordinary "me too" cars, not up to the company's high standard of innovation. Because Citroën was owned by Michelin as a sort of research laboratory, such experimentation was possible. Citroën finally did introduce the clever Citroën GS in 1970, which sold a spectacular 2.5 million units.

DS in the US

While the DS was a hit in Europe, it seemed rather odd in the United States. Ostensibly a luxurious car, it did not have the basic features that buyers of that era expected to find on such a vehicle - fully automatic transmission, air conditioning, power windows and a reasonably powerful engine. The DS price point was similar to the contemporary Cadillac luxury car. Also, people at the time wanted only the newest models, which changed every year, like fashion, yet the DS appeared vaguely derivative of the 1950 Hudson Hornet step-down design.

Outdated US legislation also banned one of the car's more advanced features, aerodynamic headlamps, now common in US automobiles. Ultimately, 38,000 units were sold. The first year of the aerodynamic glass over the DS' headlights along with driving lights turned by the steering, was also the first year these features were outlawed in the US.

Design variations

The DS always maintained its size and shape, with easily removable, unstressed body panels, but certain design changes did occur.

A station wagon version was introduced in 1958. It was known by various names in different markets (Break in France, Safari and Familiale in the UK, Wagon in the US, and Citroën Australia used the terms Safari and Station-Wagon). It had a steel roof to support the standard roof rack.

In September 1962, the DS was restyled with a more aerodynamically efficient nose, better ventilation and other improvements. It retained the open two headlamp appearance, but was available with an optional set of driving lights mounted on the front fenders. In 1965 a luxury upgrade kit, the DS Pallas (after Greek goddess Pallas), was introduced. This included comfort features such as better noise insulation, leather upholstery and external trim embellishments.

In 1967, the DS and ID was again restyled. This version had a more streamlined headlamp design, giving the car a notably shark-like appearance. This design had four headlights under a smooth glass canopy, and the inner set swivelled with the steering wheel. This allowed the driver to see 'around' turns, especially valuable on twisting roads driven at high speed at night.

However, this feature was not allowed in the US at the time (see World Forum for Harmonization of Vehicle Regulations), so a version with four exposed headlights that did not swivel was made for the US market.

The station wagon edition, the Break (called the ID Safari on the UK market) and "Familiale", was also upgraded. The hydraulic fluid changed in all markets (except the US) to the technically superior LHM (Liquide Hydraulique Minérale).

Rarest and most collectible of all DS variants, a convertible was offered from 1958 until 1973. The convertibles were built in small series by French carrossier Henri Chapron, for the Citroën factory. In addition, Chapron also produced a few coupés, non-works convertibles and special sedans (DS Lorraine for instance).

DS engines

As with all French cars, the DS design was impacted by the tax horsepower system, which effectively mandated very small engines.

Unlike the Traction Avant predecessor, there was no top-of-range model with a powerful six cylinder engine. The DS was designed around an air cooled flat six based on the design of the 2 cylinder engine of the 2CV, similar to the motor in the Porsche 911. Technical issues forced this idea to be scrapped.

Thus, for such a modern car, the engine of the original DS 19 was also old-fashioned. It was derived from the engine of the 11CV Traction Avant (models 11B and 11C). It was an OHV four-cylinder engine with three main bearings and dry liners, and a bore of 78 mm and a stroke of 100 mm, giving a volumetric displacement of 1911 cc. The cylinder head had been reworked; the 11C had a reverse-flow cast iron cylinder head and generated 60 hp at 3800 rpm; by contrast, the DS 19 had an aluminium cross-flow head with hemispherical combustion chambers and generated 75 hp at 4500 rpm. Apart from these details, there was very little difference between the engines: even the locations of the cylinder head studs were the same, so that it was possible to put the cylinder head of a DS on a Traction Avant engine and run it.

Like the Traction Avant, the DS had the gearbox mounted in front of the engine, with the differential in between. Thus the DS is a really a mid engine front wheel drive car. It initially had a four-speed transmission and clutch, operated by a hydraulic controller. To change gears, the driver flicked a lever behind the steering wheel to the next position and eased-up on the accelerator pedal. The hydraulic controller disengaged the clutch, engaged the nominated gear, and re-engaged the clutch. Manual transmission control was a lower-cost option. The later and simpler ID19 also had the same gearbox and clutch, manually operated. In the 1970s a five-speed manual and 3-speed fully-automatic were introduced, in addition to the original four-speed unit.

The DS and ID powerplants evolved throughout its 20 year production life. The car was underpowered and faced constant mechanical changes to boost the performance of the four-cylinder engine. The initial 1911 cc 3 main bearing engine (carried forward from the Traction Avant) of the DS 19 was replaced in 1965 with the 1985 cc 5 bearing motor of the DS 19a (called DS20 from September 1969).

The DS 21 was also introduced for model year 1965. This was a 2175 cc, 5 main bearing engine. This engine received a substantial increase in power with the introduction of Bosch electronic fuel injection for 1970, making the DS one of the first mass-market cars to use electronic fuel injection.

Lastly, 1973 saw the introduction of the 2347 cc engine of the DS 23 in both carbureted and fuel injected forms. The DS 23 with electronic fuel injection was the most powerful production model, producing 141 horsepower.

IDs and their variants went through a similar evolution, generally lagging the DS by about one year. ID models never received the DS 23 engine or fuel injection. The DS was offered with a number of transmission options, including the "Hydraulique" 4-speed semi-automatic, 4-speed and 5-speed manuals and a 3-speed Borg-Warner full-automatic. The full-automatic transmissions were intended for the US market, but as Citroën withdrew from the US in 1972, the year of highest US sales, due to constrictive road rules, most automatic DSs, being the DS 23 EFI sedans with air conditioning, were sold in Australia.

Citroen 2CV Berline, 1963

Citroen 2CV Berline, 1963



The Citroën 2CV (French: deux chevaux, literally "two horses", from the tax horsepower rating) was an economy car produced by the French automaker Citroën from 1948 to 1990.

The 2CV belongs to a very short list of vehicles introduced right after World War II that remained relevant and competitive for many decades - in the case of the 2CV, 42 years.

During the German occupation of France during World War II, Michelin (Citroën's main shareholder) and Citroën managers decided to hide the TPV project from the Nazis, fearing some military application. Several TPVs were buried at secret locations, one was disguised as a pickup, and the others were destroyed, and Boulanger had the next six years to think about more improvements. Until 1994, when three TPVs were discovered in a barn, it was believed that only two prototypes had survived. As of 2003, five TPVs are known. For long it was believed that the project was so well hidden that the all the prototypes were lost at the end of the war (in fact it seems that none of the hidden TPVs was lost after the War, but in the 1950s an internal memo ordered them to be scrapped. The surviving TPVs were, in fact, hidden from the top management by some workers who were sensitive to their historical value).

After the war, internal reports at Citroën showed that producing the TPV would not be economically viable, given the rising cost of aluminium in the post-war economy. A decision was made to replace most of the aluminium parts with steel parts. Other changes were made, the most notable being an air-cooled engine, new seats and a restyling of the body by Flaminio Bertoni. It took three years for Citroën to rework the TPV and the car was nicknamed "Toujours Pas Vue" (Still Not Seen) by the press.

Citroën finally unveiled the car at the Paris Salon in 1948. The car on display was nearly identical to the type A version that would be sold next year, but lacked an electric starter: the addition of this one was decided the day before the opening of the Salon of Paris. It was enormously criticized. In spite of that, it had a great impact on low-income population.

It was laughed at by journalists, probably because Citroën had launched the car without any press advertising. Boris Vian described the car as an "aberration roulante" (rolling aberration) and the car was qualified as a "Spartan car" or a "sardine can" by many. History has confirmed that the car was charming in a lot of people's views, and a revolution in consumer transportation, at least on the French market.

The 2CV was a great commercial success: within months of it going on sale, there was a three-year waiting list. The waiting list was soon increased to five years. At that time a second-hand 2CV was more expensive than a new one because the buyer did not have to wait. Production was increased from four units per day in 1949 to 400 units per day in 1950. Some of the early models were built at Citroën's plant in Slough, England but the 2CV sold poorly in Great Britain in part due to its excessive cost. Expecting to boost sales, Citroën introduced a glass-fibre coupé version called the Bijou that was briefly produced at Slough. Styling of this little car was by Peter Kirwan-Taylor who was better known for his work with Colin Chapman of Lotus cars, but it proved to be too heavy for the diminutive engine to endow it with adequate performance.

In 1967 Citroën built a new car based on the 2CV, the Citroën Dyane, in response to the direct competition by the Renault 4. At the same time, Citroën developed the Méhari off-roader.

A rare Jeep-esque derivative, called the Yagán, after an Aborigine tribe, was made in Chile between 1972 and 1973. After the Chilean coup of 1973, there were 200 Yagáns left that were used by the Army to patrol the streets and the Peruvian border, with 106 mm cannons.

A similar car was sold in some west African countries as the Citroën "Baby-brousse".

A very special version of the 2CV was the «Sahara» for very difficult off-road driving, built from December 1960 to 1971. This one had an extra engine mounted in the rear compartment and both front and rear wheel traction. Only 694 «Sahara»s were built.

The purchase price of the 2CV was always very low. In Germany in the 1960s for example, it cost about half as much as a Volkswagen Beetle.

As time went on, this rural horse-substitute gained favor with a new audience: European nonconformists who protested mass consumer culture. At the time, a popular joke was that 2CVs came straight from the factory with Atomic Power - No Thanks! bumperstickers. Owning a 2CV was like being in a club - 2CV owners would wave to each other on the road.

The 2CV was mainly sold in France and some European markets. In the post war years, Citroën was very focused on the home market, which had some unusual quirks, like puissance fiscale. The management of Michelin was indulgent of Citroën up to a point, but was not prepared to initiate the investment needed for the 2CV (or the Citroën DS for that matter) to truly compete on the global stage. Consequently, the 2CV suffered a similar fate to the Morris Minor and Mini, selling fewer than 10 million units, whereas the Volkswagen Beetle, which was sold worldwide, sold 21 million units.

In Iran, the Citroën 2CV was called the Jian. The cars were originally manufactured in Iran in a joint venture between Citroën and Iran National up until the 1979 Revolution, when Iran National was nationalized, which continued producing the Jian without the involvement of Citroën.

Only a few thousand 2CVs were sold in North America when they were new - the car was so small and inexpensive that the cost of transport alone put it into a different and uneconomic price category. The 2CV was built in Chile and Argentina to address this issue for South America.

Construction

The level of technology in the 1948 2CV was remarkable for a car of any price in that era, let alone one of the cheapest cars on the planet. While colors and detail specifications were modified in the ensuing 42 years, the biggest mechanical change was the addition of front disc brakes in 1981 for the 1982 model year.

The 1948 2CV featured:
    * four wheel independent suspension that was inter-connected front to rear on the same side under certain conditions
    * leading arm front suspension
    * trailing arm rear suspension
    * rear fender skirts
    * front-wheel drive
    * inboard front brakes
    * small, lightweight, air-cooled flat twin engine
    * 4-speed manual transmission
    * bolt-on detachable body panels
    * front suicide doors
    * detachable full length fabric sunroof and boot lid — for load carrying versatility

The body was constructed of a dual H-frame chassis, an airplane-style tube framework, and a very thin steel shell.

The suspension of the 2CV was almost comically soft — a person could easily rock the car back and forth dramatically. The leading arm / trailing arm swinging arm, fore-aft linked suspension system together with inboard front brakes had a much smaller unsprung weight than existing coil spring or leaf designs. The interconnection transmitted some of the force deflecting a front wheel up over a bump, to push the rear wheel down on the same side. When the rear wheel met that bump a moment later, it did the same in reverse, keeping the car level front to rear. This made the suspension more responsive, enabling the 2CV to indeed be driven at speed over a ploughed field. Since the rear brakes were outboard, extra shock absorbers or tuned mass dampers were fitted to the rear wheels to damp wheel bounce.

Front-wheel drive made the car easy and safe to drive and Citroën had developed some experience with it due to the pioneering Traction Avant.

It was powered by a flat-twin air-cooled engine designed by Walter Becchia, with a nod to the classic 'boxer' BMW motorcycle engine (it is reported that Becchia dismantled the engine of the BMW motorcycle of Flaminio Bertoni before designing the 2CV engine).

The car had a 4-speed manual transmission, an advanced feature on an inexpensive car at the time. Boulanger had originally insisted on no more than 3 gears, because he believed that with four ratios the car would be perceived as complex to drive by customers. Thus, the fourth gear was marketed as an overdrive, this is why on the early cars the "4" was replaced by "S" for surmultipliée. The gear shifter came horizontally out of the dashboard with the handle curved upwards. It had a strange shift pattern. The first was back on the left, the second and third were inline and the fourth (or the S) could be engaged only by turning the lever to the right from the third.

In keeping with the ultra-utilitarian (and rural) design brief, the canvas roof could be rolled completely open. The Type A one stoplight, and was available only in grey. The windscreen wipers were powered by a purely mechanical system: a cable connected to the transmission, to reduce cost, this cable powered also the speedometer. The wipers' speed was therefore variable with car speed. When the car was waiting at a crossroad, the wipers were not powered, thus it was also possible to power them by hand.

The reliability of the car was increased by the fact that, being air-cooled, it had no coolant, radiator, water pump or thermostat. It had no distributor either because both spark plugs were fired at the same time, on every two strokes. Except for the brakes there were no hydraulic parts on original models as the shock absorbers were based on an inertial system.

Engines
The car featured an air-cooled, flat-twin, four-stroke, 375 cc engine, with the notoriously underpowered earliest model developing only 9 bhp DIN (6.5 kW). A 425 cc engine was introduced in 1955, followed by a 602 cc (giving 28 bhp (20.5 kW) at 7000 rpm) in 1968. With the 602 cc engine the tax classification of the car changed so that it became in fact a 3CV, but the commercial name remained unchanged. A 435 cc engine was introduced at the same time in replacement of the 425 cc, the 435 cc engine car was christened 2CV 4 while the 602 cc took the name 2CV 6 (nevertheless it did take the name 3CV in Argentina). The 602 cc engine evolved to 33 bhp (24 kW) in 1970; this was the most powerful engine fitted to the 2CV. A new 602 cc giving only 29 bhp (21.5 kW) at a slower 5750 rpm was introduced in 1979. Despite being less powerful, this engine was more efficient, allowing lower fuel consumption and better top speed, at the price of decreased acceleration.

The 2cv also pioneered the use of the now common Wasted spark Ignition System, also known as the DIS (Distributorless Ignition System) ignition using a double ended coil fired on each revolution, (on the exhaust and compression stroke), by just a contact breaker.


The end of the 2CV

The 2CV was produced for 42 years, the model finally succumbing to customer demands for speed and safety, areas in which this ancient design had fallen significantly behind modern cars.

Citroën had attempted to replace the ultra-utilitarian 2CV several times (with the Dyane, Visa, and the AX), however its comically antiquated appearance became an advantage to the car and it became a niche product which sold because it was different from anything else on sale.

While not a replacement for the 2CV, a straightforward, unremarkable urban runabout supermini like the Citroën AX seemed to address the automaker's requirements at the entry level in the 1990s.

In 1988, production ceased in France but was continued in Portugal. The last 2CV, gray with chassis number VF7AZKA00LA376002, rolled off the Portuguese production line on July 27, 1990. In all, a total of 3,872,583 2CV sedans were produced. Including the commercial versions of the 2CV, Dyane, Méhari, FAF, & Ami variants, the 2CV's underpinnings spawned over nine million cars.

Tuesday, December 28, 2010

Lancia Beta, 1909

Lancia Beta, 1909



Lancia Beta, 1909

Lancia Gamma 20HP, 1910

Lancia Gamma 20HP, 1910


Lancia Gamma 20HP, 1910

Lancia Alpha 12Hp, 1907


Lancia Alpha 12Hp, 1907



Lancia Alpha 12Hp, 1907

Monday, December 27, 2010

Bentley S1 Continental, 1956

Bentley S1 Continental, 1956


The Bentley S1 was a luxury car produced by Bentley Motors Limited from 1955 through 1959. It marked Bentley parent, Rolls-Royce, reducing the differences between their Bentley and Roll-Royce models, with the S1 differing only in its radiator design and badging from the Rolls-Royce Silver Cloud I.

The models shared the 4.9 L (4887 cc/298 in³) straight-6 engine, with this being the last vehicle to use this engine. The bore was 95.25 mm (3.7 in) and the stroke was 114.3 mm (4.5 in). Twin SU carburetors were fitted, with upgraded models from 1957. A 4-speed automatic transmission was standard, with a 4-speed manual available as an option. Two wheelbases were produced: 123 in (3124 mm) and, from 1957, 127 in (3226 mm).

Bentley S1, 1955

Bentley S1, 1955



The Bentley S1 was a luxury car produced by Bentley Motors Limited from 1955 through 1959. It marked Bentley parent, Rolls-Royce, reducing the differences between their Bentley and Roll-Royce models, with the S1 differing only in its radiator design and badging from the Rolls-Royce Silver Cloud I.

The models shared the 4.9 L (4887 cc/298 in³) straight-6 engine, with this being the last vehicle to use this engine. The bore was 95.25 mm (3.7 in) and the stroke was 114.3 mm (4.5 in). Twin SU carburetors were fitted, with upgraded models from 1957. A 4-speed automatic transmission was standard, with a 4-speed manual available as an option. Two wheelbases were produced: 123 in (3124 mm) and, from 1957, 127 in (3226 mm).

A somewhat sportier coachbuilt-only S1 Continental was introduced six months later.

Production
S1: 3072 (145 with coachbuilt bodies)
S1 long wheelbase: 35 (12 with coachbuilt bodies)
S1 Continental: 431

Acura TL ASPEC Concept, 2003

Acura TL ASPEC Concept, 2003

 
 
 

Powertrain
+ 300+ horsepower, powertrain including:
- Performance-tuned 3.2-liter, 24-valve, V-6 engine
- High flow intake and exhaust
- 6-speed close-ratio manual transmission with limited-slip differential

Suspension
+ A-SPEC high performance suspension with track-tuned shocks and springs
+ 21-inch prototype alloy wheels
+ High performance tires
+ Brembo 4-wheel disc brakes with 8-piston calipers and 15-inch rotors

Body/Styling
+ Panoramic glass roof
+ Larger, high-flow exhaust finishers
+ 42 mm wider track
+ Wider fender flares
+ Trunk lid spoiler
+ Redesigned front bumper with larger Acura grille and lower air intakes
+ Redesigned rear bumper
+ 3-stage silver-gray Mica Pearl paint
+ New finish treatment on headlights/tail lights, clear side indicators

Interior
+ Premium Matador Red sport/luxury interior
+ Deeply bolstered custom leather seats with heating and cooling ventilation
+ Ultra suede headliner
+ Carbon/Kevlar accents on door panels and center console
+ Carbon/Kevlar sport steering wheel
+ Aluminum shift knob and foot pedals
+ Rear bucket seats with storage

Technology/Safety
+ Adaptive Cruise Control
+ Rearview camera

Acura 3.2 CL Type-S, 2003

Acura 3.2 CL Type-S, 2003


 

Powertrain
While it continues to come with a 5-speed Sequential SportShift automatic transmission, the CL Type-S now offers a new close ratio 6-speed manual transmission as well. Models with the new manual transmission feature:
- Helical limited slip differential
- Curb weight of 3446 lbs. (compared to 3510 lbs. for the CL Type-S with automatic transmission)
- Multi-cone synchronizers
- Self-adjusting clutch with dual-mass flywheel
- Short-throw shift linkage

Chassis

+ CL Type-S with manual transmission replaces the VSA found in the CL Type-S with automatic transmission with new helical limited slip differential
+ New 6-spoke 16 inch wheels (3.2 CL)
+ New 6-spoke 17 inch wheels (CL Type-S)
+ CL Type-S with manual transmission adds two hydraulic engine mount dampers to counter engine movement

Body

Front Styling
+ Revised grille with body-colored surround
+ Revised headlights with black accents
Rear Styling
+ Revised taillight lenses with clear upper portion
+ New exhaust finishers

Safety/Convenience

+ OnStar(R) is standard equipment on CL models equipped with the Acura Satellite-Linked Navigation System
+ Lower Anchors and Tethers for Children (LATCH) System added on outboard rear seats for child safety seat attachment
+ Driver's Dual Stage Supplemental Restraint System (SRS)
+ Auto-up driver's side window

Interior Styling

CL Type-S
+ Models with black interiors receive titanium-look trim on doors and center console
+ In models with 6-speed manual transmission, center console redesigned to accommodate manual shifter and hand-operated parking brake
+ Perforated leather door inserts

Sunday, December 26, 2010

Lamborghini 400 GT, 1966

Lamborghini 400 GT, 1966

 

The Lamborghini 400GT 2+2 was a 2+2-seated sports car from the Italian manufacturer Lamborghini, successor to the 350GT. First presented at the 1966 Geneva Auto Show.

Compared to its predecessor the engine was enlarged to 3,929 ccm (240 c.i.), increasing the power to 320 bhp. The 400GT 2+2 was actually a different body from the 350GT, with a longer wheelbase, different roofline, and some sheetmetal changes throughout the car. The larger body shape enabled the +2 seating to be installed in the rear, where the 350GT only had room for luggage or +1 seating. The bodywork was designed by Carrozzeria Touring. The 400GT 2+2 also had a Lamborghini designed gearbox, with Porsche style synchromesh on all gears including, which greatly improved the drivetrain.

There was a variant of the 350GT with the 4L V12 fitted to it, which was called the 400GT. Only 23 of these smaller coupes were built, three of which had desirable aluminium bodywork.

A total of 247 units were built from 1966 to 1968, when it was replaced with the Islero.

Lamborghini 350 GTS Spider, 1966

Lamborghini 350 GTS Spider, 1966



The Lamborghini 350GT was the first production car by Lamborghini, first shown at the Turin Motor Show in 1963.

The car featured a 3.5 litre quad-cam V-12 engine (hence its designation), independent rear suspension (while Ferrari still used live rear axles) and a controversial 2+1 semi-fastback body by Carrozzeria Touring of Milan.

The 350GT generally drew high praises at the time for its flexible and high-revving engine, its stable cornering, even on rough surfaces, and its high level of finish. 120 copies were built from 1963 to 1966.

Lamborghini 350 GT, 1964

Lamborghini 350 GT, 1964


 

The Lamborghini 350GT was the first production car by Lamborghini, first shown at the Turin Motor Show in 1963.

The car featured a 3.5 litre quad-cam V-12 engine (hence its designation), independent rear suspension (while Ferrari still used live rear axles) and a controversial 2+1 semi-fastback body by Carrozzeria Touring of Milan.

The 350GT generally drew high praises at the time for its flexible and high-revving engine, its stable cornering, even on rough surfaces, and its high level of finish. 120 copies were built from 1963 to 1966.

Saturday, December 25, 2010

Buick Super-Series 50, 1948

Buick Super-Series 50, 1948 




Buick Super-Series 50, 1948

Buick Convertible, 1948

Buick Convertible, 1948

Buic Convertible, 1948

Buic Super Estate Wagon, 1940

Buic Super Estate Wagon, 1940


Buic Super Estate Wagon, 1940

BMW 328, 1936


BMW 328, 1936

 
 
In the mid-30s, production roadsters and competition cars were still very similar in technical terms - and motorsport was still the ideal place to prove the performance and reliability of a production car. But to keep up with the competition, BMW soon had to build cars with more power and muscle. So BMW's engineers looked for ways and means to significantly increase engine output without increasing engine size. And they found the solution - the M328, the engine powering the legendary BMW 328 sports car in 1936.

Right from the start in its debut at Nürburgring on 14 June 1936, BMW's new roadster literally pulverised even the most powerful supercharged competitors. This outstanding success was attributable to the well-balanced combination of superior engine power and cutting-edge suspension technology characteristic of BMW roadsters to this day: 80 hp in the regular version and low weight of just 830 kg or 1,830 lb gave this elegant roadster superior performance still impressive today.

The BMW 328 Roadster initially being restricted to motorsport as of mid-1936, production of the series model started in spring 1937. And so this high-performance sports car was driven not only by BMW's works drivers, but also by private customers since, over and above racing, it was very well suited for everyday use. And with its top speed of 155 km/h or 96 mph, this was indeed one of the fastest cars on the road back then.

The BMW 328 Roadster remained a very rare bird, with only 464 units of this classic roadster being built up to 1940.